前段时间讨论过DC光头是否可以用光驱和硬盘代替读盘,下面贴几张图仅提供欣赏.这说明DC改机DIY还是有可能的,只要努力就会有成果!



文字说明：


Dreamcast CDRW tutorial

Updated 2005-01-21 : Added some pictures
First version 2005-01-19

Warning this modification could shorten the lif of your dreamcast.

I tried to set my dreamcast up to be able to read cdrw using some tutorials on the Internet, but it wouldn't work, in fact the 450 ohms resistor I used was too low (300 Ohms in parallel), I hooked up a trimmer in parallel with the optical unit's trimmer and made some tests (the values I give are for parallel resistors) :
530 ohms   :   CDR works   CDRW does not
507 ohms   :   CDR works   CDRW does not
475 ohms   :   CDR seems to start having trouble reading   CDRW works !
430 ohms   :   CDR makes ugly sounds   CDRW works
395 ohms   :   CDR more noise still works   CDRW works
342 ohms   :   CDR does not work   CDRW works
320 ohms   :   neither work.

I tried two different brands of CDRW, both worked (but I made all the tests with only one). I had to use a boot disc, autoselfboot CDRW never worked.

So I must use a resistor in between 475 and 342 ohms, that's for parallel value, as the optical unit's trimmer is set to about 900ohms it gives me 1005ohms and 550ohms for extreme limits.
If you want to try by yourself make some experimentations with a 10K trimmer.

Warning it may be dangerous for the laser diode to use values too low, don't go under 200 ohms in parallel.

Here's how I soldered my wires :

First you'll have to open your dreamcast, I assume you're able to do so (and you can solder without messing the components around).
Remove the optical unit, only 3 screws and here you go.
Open the optical unit, there's 5 screws, two of them are hidden under the black pad (where I put red dots on the image below) if you manage to make the solders without disconnecting the wires, fine, because they're hard to reconnect.


You have to solder two wires to the two leftmost pins of the ribbon cable connector (in fact those two pins lead directly to the two pins of the optical unit trimmer on which other cdrw tutorials said to solder wires)


Beware not to melt the ribbon if soldering like this.


A good place for the wires through the shield is the hole for the screw (see picture 1 too)


Then close the optical unit


Solder a resistor (or a trimmer for testing) and a switch at the end of the wires


Make a hole in the dreamcast body and here you are.






Of course I don't take responsability if you burn anything trying to follow this tutorial, this come with hope that it can be useful, but without any warranty.

200G硬盘足够了,硬盘现在也不太贵,毕竟DC游戏全部的就那些.主要还是不用刻盘也不用为读盘等太长的时间,而且不会有读盘的声音的说~

多谢版主提供文本,这么多英文看不明白就已经知道是很麻烦了-_-!

晕~不是吧.不过读CDRW那也挺好的,可以玩够一个游戏就可以从盘里擦掉了,HOHO.不过好象没多少人关注这些~

还是等专业人事确认以后再动手,别把自己DC玩砸了~

慢慢来吧,什么都是一步一步来的,说不定什么时候能接硬盘了呢~

尤其还有些不知道是虾米的电路版,不知道什么,一窍不通~~

引用

下面是引用glf999于2005-10-25 10:02发表的:
这个就是将DC改机(加功率调整)

让DC 读 CDRW 盘的,和接硬盘一点关系都没有到是

我以前得到过一个电路图,是利用那个接猫的扩展接口
.......

好哦,能发上来看看最好了~

没拆开看过,是借口应该也不能直接用的,软件和硬件都不支持~